Spraying Clear Coat Over Decals

Spraying Clear Coat Over Decals. A pain to work with. If you didn't use water or any kind of transfer agent, then it doesn't matter.

Decals over or under clearcoat Page 2 KZRider Forum KZRider, KZ from www.kzrider.com

A pain to work with. Very gentle light dusting coats first to seal over the decal, and gradually build up the layers, followed by a “wet” coat to finish. Spray base coats, clear it with a couple of coats.

Source: www.flickr.com

Again wait till the previous layer is sticky dry. 6 or 7 should do it.

Source: www.woodweb.com

Very gentle light dusting coats first to seal over the decal, and gradually build up the layers, followed by a “wet” coat to finish. If lacquer clear is sprayed over decals too quickly or heavily, the solvents in the lacquer will destroy the decals under it.

Source: k2forums.com

I believe the same method will be fine. The first body i noticed if the lacquer / clear went on too thick it seemed to react and almost bubble the decals.

Source: www.modelcarsmag.com

Good luck with your project! Very gentle light dusting coats first to seal over the decal, and gradually build up the layers, followed by a “wet” coat to finish.

Source: www.kzrider.com

It did leave an eggshell texture finish on the decal which wasn’t ideal but it did seal the decal. Good luck with your project!

Source: customboatrepairs.com

Some guys i know in texas put stickers all over their body work, then do a gac glue clear coat over it, and then airbrush clear paint over that. The second body i applied 2 thin mist like coats to.

Source: fullintensitygrafx.com

In general the sheets is now ready, you can spray a third layer just like layer two but now moving in the width. If lacquer clear is sprayed over decals too quickly or heavily, the solvents in the lacquer will destroy the decals under it.

Source: www.rccrawler.com

There are two types now available. Bury it in clear with at least four coats.

Source: www.pinterest.jp

The second body i applied 2 thin mist like coats to. If you didn't use water or any kind of transfer agent, then it doesn't matter.

Source: www.rccrawler.com

Again wait till the previous layer is sticky dry. Spraymax 2k clear the spraymax 2k clear spray paint contain solvents that will melt the ink on the decals.

Source: singletrackworld.com

Some guys i know in texas put stickers all over their body work, then do a gac glue clear coat over it, and then airbrush clear paint over that. A pain to work with.

Source: www.pinterest.com

Because it's a lacquer based paint, it can have some bad effects on decals. Yes you can clear coat over stickers/ decals only catch is it will have the edge to it when you clear coat over it if your wanting the edge to not show give it 2 good coats let dry sand with 600 grit and reshoot with at least 2 good coats and wetsand and buff!!!

There Are Two Types Now Available.

The first body i noticed if the lacquer / clear went on too thick it seemed to react and almost bubble the decals. Flex seal clear activated at two and a half minutes of being submerged and applied well to surface. Sounds like from what i’ve read, and what dixie said, some clear coats may attack the vinyl decals, and there could be an issue with the clear coat.

Generally, A Clear Coat Paint Is Sprayed On The Sticker Surface For Applying A Clear Coat.

5 minute cure time after three coats were applied: A pain to work with. The first coat was rough, of course, because it was so thin.

Very Gentle Light Dusting Coats First To Seal Over The Decal, And Gradually Build Up The Layers, Followed By A “Wet” Coat To Finish.

Wet sand the clear with 1000 grit very carefully to. Lacquer clearcoat can be applied over decals, but it must be applied very slowly and carefully. Good luck with your project!

Bury It In Clear With At Least Four Coats.

It's a good idea to spray a gloss clear coat over the decals. Spray your base coat, apply the decal and bury it in the clear. Flex seal clear sealing results on hayes paper co® inkjet waterslide decal paper.

Scuff The Clear With 400 And Wipe Clean With Grease And Wax Remover, Lay The Decals And Use A Scuff Pad To Lightly Scuff The Decal.

Applying clear coat to decals is a normal part of my business. If you didn't use water or any kind of transfer agent, then it doesn't matter. When i say mist, i really mean mist.